Yamaha RD 500 LC and Suzuki RG500 Gammaby Darren Rycroft

8 april 2015 | Forfatter: | Comments Off på Yamaha RD 500 LC and Suzuki RG500 Gammaby Darren Rycroft
Yamaha RD 500 LC

Yamaha RD 500 LC and Suzuki RG500 Gamma – by Darren Rycroft

I picked up this comment from our Facebook Group pages. I always liked people who can write about bikes and cars with such passion and zest…

“ GP500 bikes were only ever ridden by ‘Demi-gods’…Animals to tame and only ever tamed by a very select few…The golden era of GP racing when the riders all had balls bigger than footballs and more talent in their throttle hand than most of us have in our entire bodies…I can honestly say that following the GP’s of that era was something to behold…The smell and the noise of a 500cc 2 stroke on full chat is something which stays with you and cannot be replicated, even with the latest MOTO GP bikes…

Some of the classic road versions like the Yamaha RD500 and the Suzuki RG500 Gamma were as close as you would get and great fun to ride….

Ahhhh, the good old days…”

Be sure to visit Darren’s Web Galleries.

Yamaha RD500 LC

Development

With the success in the early 1980s of Kenny Roberts and the Yamaha YZR500 in Grand Prix motorcycle racing Yamaha realised that a road going replica of their 500 cc racing machine would sell well. Using the similar technology of the smaller RD series of two stroke motorcycles the RD500LC was launched in 1984 to an enthusiastic riding public.

Engine

The RD500LC uses a 50-degree, twin-crankshaft V4 engine layout. Linked Yamaha YPVS exhaust power valves are controlled by a single electronic unit and servo motor and are designed to give a broader power band. The engine also featured intake reed valves unlike the YZR500 racer which used rotary disc valve induction.

The reed valves used two different intake arrangements, the lower cylinders were fed through crankcase mounted reeds; the upper pair used cylinder barrel mounted reeds. The four Mikuni carburettors are side mounted in pairs and feed each cylinder through 90 degree intake manifold. The lower expansion chambers exit normally but the upper pipes cross over each other just behind the exhaust ports to maintain the correct tuned length.

The dual crankshafts are geared directly to the clutch, while the front crankshaft also drives a counter balancer shaft mounted between the two crankshafts. The counter balance shaft, unusual on a two-stroke, assists with dampening engine vibrations. The engine is cooled by thermostatically controlled liquid cooling, an auxiliary electric fan mounted behind the radiator cuts in at high temperatures (e.g. when stationary in traffic).

Lubrication is by direct injection in to the inlet manifolds using Yamaha’s ‘Autolube’ pump system, normally controlled in other two-stroke engines by throttle position the engine oil pump is controlled by the YPVS servo motor ensuring that the oil supply is not shut off at high engine revolutions.

Transmission

The RD500LC uses a six speed sequential close ratio gearbox, the gear shafts are removable from the right side of the engine without the need to split the crankcases. The clutch is of the wet, multiple-disc coil spring type and is cable operated. Unusually for a two-stroke engine the gears and outer crankshaft bearings are lubricated by a separate crankshaft driven troichoid oil pump.

Final drive is by O-ring chain and sprockets.

Chassis

The frame of the RD500LC is manufactured from mild steel box-section and uses a perimeter layout. The rear shock absorber is unusually placed horizontally under the engine and uses the lower crankcase as a mounting point. The under-seat area is occupied by the upper cylinder exhaust chambers, the battery and the YPVS servo motor.

The rear of the shock absorber connects to an extruded aluminium alloy swinging arm via several forged aluminium rocker arms. An unusually small diameter 16″ wheel is held between 37 mm (1.5 i) spring and oil damped forks

which featured adjustable anti-dive units. The RD500LC used twin ventilated disc brakes for the front wheel with a single ventilated disc at the rear. A solo seat cowl was originally provided to cover the pillion seat when not in use.

Yamaha RD 500 LC

Electrical system

RD500LC Speedometer and Tachometer

The RD500LC features a standard 12 volt electrical system. Yamaha’s self cancelling indicator unit is used and a variable resistance gauging system is used to monitor two-stroke oil tank contents with associated warning lights. Nippondenso Capacitor Discharge Ignition (CDI) is used in conjunction with two coils.

RZV500R

The RZV500R was designed exclusively for the Japanese home market although many have been exported privately. The RZV500R features upgraded parts not found on the standard RD500LC. A major difference is the hand-welded aluminium frame, which is significantly lighter than the steel version used on standard models.

The front brake lines are braided stainless steel instead of rubber coated, and the front forks are air assisted with rebound damping adjustment. The rear brake and gear levers are cast from aluminium, as are the clip-on type handle bars. These chassis modifications added up to a weight saving of 20 lb (9.1 kg).

The engine was detuned to 64 hp (48 kW) to comply with Japanese legislation, this was achieved by restricting the internal diameter of the exhaust pipes.

Suzuki RG500 Gamma

Model: Suzuki RG 500 Gamma

Year: 1986

Displacement: 498.00 ccm (30.39 kubikk inches)

Yamaha RD 500 LC
Yamaha RD 500 LC
Yamaha RD 500 LC
Yamaha RD 500 LC
Yamaha RD 500 LC


interessante artikler

Tagged as:

Andre artikler i kategorien "Yamaha":

Oversettelse
 Rediger oversettelse
Våre partnere
Følg oss
Kontakt oss
våre kontakter

dima911@gmail.com

Født i Sovjetunionen

423360519

Om dette nettstedet

For alle spørsmål om reklame, Vennligst kontakt oppført på området.


Motorsykler katalog med spesifikasjoner, bilder, rangeringer, anmeldelser og discusssions om Motorsykler.