Engine Break in or run in guide for new Yamaha FZ-S / FZ-16 / Fazer …

27 Фев 2015 | Author: | Комментарии к записи Engine Break in or run in guide for new Yamaha FZ-S / FZ-16 / Fazer … отключены

Engine break in or run in guide for new FZ-S / FZ-16 / Fazer

One of the most styling and appealing bike in India is the Yamaha and FZ-16 where as Fazer is a good tourer with engine and supper balance with ride quality. All three bikes share engine / gearbox and drive along with breaks and

As an owner, one would love to the throttle and taste the performance of machines, asap of the delivery but for lasting performance and engine one should do the opposite as running-in or break in process.

What is run in or break in ?

During few early newly made or machined parts or surface may make and these surface will in  quickly, thus every gives a simple easy line which an user follow to break in / running in new bike.

What if you don’t follow the in / engine break-in guide ?

We all how excited we all become when we go for a new For many of us, its a product of some struggle and wait, some buy it their salary, some hard fight at home, but in any its a hard earn product.

A running in contributed towards a ride expiration and longer life and better performance. You may the difference if you ride two bikes, one done proper running in and one it in side by side.

What is the engine break in or how to run in the Yamaha FZ16 / FZ-S or 150cc ?

Detailed but a general can be found in the owners manual 5-3).

General instruction as follows,

Total engine in period for Yamaha FZ-16 / and Fazer 150 is 1000 kms. is broken into two parts. is the 0-500 kms and next is the 500 kms to 1000

Do not start the engine with rev at any point of running in phase.

starting the engine in cold condition (like in morning allow the engine oil to warm up by the bike in idle for 5 mins rolling.

Within 0 to 500 kms, at any gear, do not 4500 RPM mark and never with a constant RPM. city roads over as city traffic allows you to through the gears and rev range.

500 to 1000 kms, the maximum RPM is 6000 and once again riding at a steady RPM for longer of time. Vary through the and RPM range.

Within running (0 to 1000 kms), stop 30 kms or 30 – 45 mins (depending on weather of riding for 5-10 mins to the engine to cool off. is to be done to prevent over of the engine from its idle

Avoid change of load. Try to the engine break in process single rider.

Change the oil and engine oil filter at half mark of running in (before service)

Yamaha FZ 150 N

Couple of speed with proper warmed up is needed under running in. Do it the oil change.

Which engine oil to be in Yamaha FZ-16 / FZ-S or (150cc) engine break in / in period ?

Use mineral engine oil you are in running in and follow a very drain interval while you in your engine. The stock mineral oil is just perfect for the If not found, you may choose Motul 4T Plus (Mineral) oil too.

YamaLube 20w40 Mineral Rs. 305/- (price / litter)

3000 4T Plus (Mineral) Rs. 310/- (Price / litter)

forget to change the Engine oil too while you change the oil.

Oil change interval for Bajaj 200 NS for engine break in / running in ?

the point, that you are not following a drain interval because the oil has bad, but rather to drain engine residue which is in these early kms of your You may follow longer drain after running in / engine in phase is over.

1st oil and filter at around 350 to 400 kms

2nd oil and filter  change at around 750 to 800 kms service)

Yamaha FZ 150 N
Yamaha FZ 150 N
Yamaha FZ 150 N
Yamaha FZ 150 N
Yamaha FZ 150 N
Yamaha FZ 150 N

Interesting articles

Tagged as:

Other articles of the category "Yamaha":

Our partners
Follow us
Contact us
Our contacts


Born in the USSR


About this site

For all questions about advertising, please contact listed on the site.

Motorcycles catalog with specifications, pictures, ratings, reviews and discusssions about Motorcycles.